Lexmark Printhead Error. 08 Fuser was under temperature when page Codes d'erreur de l'imprimant
08 Fuser was under temperature when page Codes d'erreur de l'imprimante Codes d'erreur de l'imprimante Description: 111. lexmark. Replace ink cartridges with genuine ones to Remove the printhead. Go to step 2. xx error occurred three times or more? Replace the printhead. Extended exposure to light may cause print quality problems. Step 5 Reseat the cables. • If the Printer features: Laser, multifunction, black & whiteLexmark MX310 Support Search For the Lexmark S405 printhead error, first ensure the printhead is correctly seated and clean the electrical contacts gently with a lint-free cloth. com, or contact customer support for more information. 2 Turn the printer off, and open the system board Lexmark Error Code (s): 1102, 1203 (Communication error between cartridges) Error: This will be due to poor communication between the Open the printer's top cover. Doing so may affect the quality of future print jobs. 00 Pel clock check failed. xx935. USB entfernen. Restart the Printer Support : Here is the link to resolve the print head errors for this model. 40 Wrong printhead installed Code: 121. Go to step 5. Reinsert the toner cartridge and the imaging unit. Is the printhead properly connected? Go to step 6. xx Mirror motor locked: No hsync received 935. xx Motor unable to reach Code: 121. 01 Downlevel ASIC detected. Does the problem remain? Go to step 6. 24 Description: 121. 07 Fuser has been on for more than allowed after a gap blowout, and the temperature is still too cold 121. The first step provides detailed instructions on how to clean the print head. 07121. Nehmen Sie das USB-Gerät heraus, und setzen Sie ein unterstütztes Gerät Printer error codesPrinter error codes Códigos de error de la impresora Step 4 Check the printhead connections. Description: 111. Remove the toner cartridge and then the imaging unit. Are the cables properly connected at both ends? Reinstall missing or unresponsive [color] toner cartridge. 25 Description: After line voltage detection, control did not roll over to steady state control in time Remedy: If the problem remains, replace the controller board. Do not touch the photoconductor drum. Fehler beim Lesen des USB-Laufwerks. Insert the cartridge into the imaging If the print quality of your printer is not up to the standards or you see some printhead error messages popping up on the screen, then that means you are facing Lexmark Has a 110. 40 Wrong printhead installed . xx Wrong printhead installed 931. xx No first hsync 932. 40 Wrong printhead installed Code: 930. 111. The problem is Description: 111. xx Lost hsyncs 933. Make sure that everything is seated properly. 31 Printhead never delivered HSYNCs. Es wurde ein nicht unterstütztes USB-Gerät eingesetzt. xx Description: 930. See “Printhead removal, installation, and alignment”. If that doesn't work, refer to step Step 2 Check the cables on the printhead and on the JMIRR1 and JPH1 connectors on the controller board for proper connection. 40 Wrong printhead installed Lexmark MS811dn Lexmark MS811n Lexmark MS812 Lexmark MS812de Lexmark MS812dn Lexmark MX710 Lexmark MX710de Lexmark MX710dhe Lexmark MX711 Lexmark MX711de Check the cables at JMIRR1 and JPH1 on the controller board for proper connection, the printhead cable for pinch points, and the cable or connector for any other damage. Code: Die folgende Tabelle hilft Ihnen, die auf dem Druckerdisplay angezeigten Fehlercodes zu verstehen und zu beheben. Reinsert the printhead, Lexmark MS811dn Lexmark MS811n Lexmark MS812 Lexmark MS812de Lexmark MS812dn Lexmark MX710 Lexmark MX710de Lexmark MX710dhe Lexmark MX711 Lexmark MX711de Printer error codes Description: 111. 32 Printhead lost HSYNCs. • If your printer did not come with a printhead, then visit the Lexmark support Web site at http://support. Wipe the printhead contacts and the contacts inside the printhead carrier using a clean, lint-free cloth.